Drip irrigation, also known as trickle irrigation equipment or micro irrigation or
localized irrigation, is an irrigation method that saves water and fertilizer by
allowing water to drip slowly to the roots of plants, either onto the soil
surface or directly onto the root zone, through a network of valves, pipes,
tubing, andemitters. It is done through narrow tubes that deliver water directly
to the base of the plant.
History of Drip irrigation[Back to Contents]
Primitive drip irrigation has been used since ancient times. Fan Sheng-Chih Shu, written in China during the first century BCE, describes the use of buried, unglazed clay pots filled with water as a means of irrigation.Modern drip irrigation began its development in Germany in 1860 when researchers began experimenting with subsurface irrigation using clay pipe to create combination irrigation and drainage systems.Research was later expanded in the 1920s to include the application of perforated pipe systems.The usage of plastic to hold and distribute water in drip irrigation was later developed in Australia by Hannis Thill.
Usage of a plastic emitter in drip irrigation was developed in Israel by
Simcha Blass and his son Yeshayahu.Instead of releasing water through tiny
holes, that are blocked easily by tiny particles, water was released through
larger and longer passageways by using velocity to slow water inside a plastic
emitter. The first experimental system of this type was established in 1959 by
Blass who partnered later (1964) with Kibbutz Hatzerim to create an famous irrigation equipment company called Netafim. Together they developed and patented the first practical
surface drip irrigation emitter.
In the United States, the first drip tape, called Dew Hose, was developed by Richard Chapin of Chapin Watermatics in the early 1960s.
Modern drip irrigation has arguably become the world's most valued innovation in agriculture since the invention of the impact sprinkler in the 1930s, which offered the first practical alternative to surface irrigation. Drip irrigation may also use devices called micro-spray heads, which spray water in a small area, instead of dripping emitters. These are generally used on tree and vine crops with wider root zones. Subsurface drip irrigation (SDI) uses permanently or temporarily buried dripperline or drip tape located at or below the plant roots. It is becoming popular for row crop irrigation, especially in areas where watersupplies are limited or recycled water is used for irrigation. Careful study of all the relevant factors like land topography, soil, water, crop and agro-climatic conditions are needed to determine the most suitable drip irrigation system and components to be used in a specific installation.
Components and operation of Drip irrigation[Back to Contents]
Components used in drip irrigation (listed in order from water source) include:
- Pump or pressurized water source
- Water filter(s) or filtration systems: sand separator, Fertigation systems (Venturi injector) and chemigation equipment (optional)
- Backwash controller (Backflow prevention device)
- Pressure Control Valve (pressure regulator)
- Main line (larger diameter pipe and pipe fittings)
- Hand-operated, electronic, or hydraulic control valves and safety valves
- Smaller diameter polytube (often referred to as "laterals")
- Poly fittings and accessories (to make connections)
- Emitting devices at plants (emitter or dripper, micro spray head, inline dripper or inline driptube)
In drip irrigation systems, pump and valves may be manually or automatically operated by a controller.
Most large drip irrigation systems employ some type of filter to prevent clogging of the small emitter flow path by small waterborne particles. New technologies are now being offered that minimize clogging. Some residential systems are installed without additional filters since potable water is already filtered at the water treatment plant. Virtually all drip irrigation equipment manufacturers recommend that filters be employed and generally will not honor warranties unless this is done. Last line filters just before the final delivery pipe are strongly recommended in addition to any other filtration system due to fine particle settlement and accidental insertion of particles in the intermediate lines.
Drip and subsurface drip irrigation is used almost exclusively when using recycled municipal waste water. Regulations typically do not permit spraying water through the air that has not been fully treated to potable water standards.
Because of the way the water is applied in a drip system, traditional surface
applications of timed-releasefertilizer are sometimes ineffective, so drip
systems often mix liquid fertilizer with the irrigation water. This is called
fertigation; fertigation and chemigation (application of pesticides and other
chemicals to periodically clean out the system, such as chlorine or sulfuric
acid) use chemical injectors such as diaphragm pumps, piston pumps, or
aspirators. The chemicals may be added constantly whenever the system is
irrigating or at intervals. Fertilizer savings of up to 95% are being reported
from recent university field tests using drip fertigation and slow water
delivery as compared to timed-release and irrigation by micro spray heads.
Properly designed, installed, and managed, drip irrigation may help achieve water conservation by reducingevaporation and deep drainage when compared to other types of irrigation such as flood or overhead sprinklers since water can be more precisely applied to the plant roots. In addition, drip can eliminate many diseases that are spread through water contact with the foliage. Finally, in regions where water supplies are severely limited, there may be no actual water savings, but rather simply an increase in production while using the same amount of water as before. In very arid regions or on sandy soils, the preferred method is to apply the irrigation water as slowly as possible.
Pulsed irrigation is sometimes used to decrease the amount of water delivered to the plant at any one time, thus reducing runoff or deep percolation. Pulsed systems are typically expensive and require extensive maintenance. Therefore, the latest efforts by emitter manufacturers are focused toward developing new technologies that deliver irrigation water at ultra-low flow rates, i.e. less than 1.0 liter per hour. Slow and even delivery further improves water use efficiency without incurring the expense and complexity of pulsed delivery equipment.
An emitting pipe is a type of drip irrigation tubing with emitters pre-installed at the factory with specific distance and flow per hour as per crop distance.
An emitter is also called a dripper and is used to transfer water from a pipe or tube to the area that is to be irrigated. Typical emitter flow rates are from 0.16 to 4.0 U.S. gallons per hour (0.6 to 16 L/h). In many emitters, flow will vary with pressure, while some emitters are pressure compensating.
Advantages of Drip irrigation[Back to Contents]
The advantages of drip irrigation are:
- Fertilizer and nutrient loss is minimized due to localized application and reduced leaching.
- Water application efficiency is high if managed correctly
- Field levelling is not necessary.
- Fields with irregular shapes are easily accommodated.
- Recycled non-potable water can be safely used.
- Moisture within the root zone can be maintained at field capacity.
- Soil type plays less important role in frequency of irrigation.
- Soil erosion is lessened.
- Weed growth is lessened.
- Water distribution is highly uniform, controlled by output of each nozzle.
- Labour cost is less than other irrigation methods.
- Variation in supply can be regulated by regulating the valves and drippers.
- Fertigation can easily be included with minimal waste of fertilizers.
- Foliage remains dry, reducing the risk of disease.
- Usually operated at lower pressure than other types of pressurised irrigation, reducing energy costs.
Disadvantages of Drip irrigation[Back to Contents]
The disadvantages of drip irrigation are:
- Initial cost can be more than overhead systems.
- the sun can affect the tubes used for drip irrigation, shortening their usable life.
- if the water is not properly filtered and the equipment not properly maintained, it can result in clogging.
- For subsurface drip the irrigator cannot see the water that is applied. This may lead to the farmer either applying too much water (low efficiency) or an insufficient amount of water, this is particularly common for those with less experience with drip irrigation.
- Drip irrigation might be unsatisfactory if herbicides or top dressed fertilizers need sprinkler irrigation for activation.
- Drip tape causes extra cleanup costs after harvest. Users need to plan for drip tape winding, disposal, recycling or reuse.
- Waste of water, time and harvest, if not installed properly. These systems require careful study of all the relevant factors like land topography, soil, water, crop and agro-climatic conditions, and suitability of drip irrigation system and its components.
- In lighter soils subsurface drip may be unable to wet the soil surface for germination. Requires careful consideration of the installation depth.
- The main purpose of drip irrigation is to reduce the water consumption by reducing the leaching factor. However when the available water is of high salinity or alkalinity, the field soil becomes gradually unsuitable for cultivation due to high salinity or poor infiltration of the soil. Thus drip irrigation converts fields in to fallow lands when natural leaching by rain water is not adequate in semi arid and arid regions.
- most drip systems are designed for high efficiency, meaning little or no leaching fraction. Without sufficient leaching, salts applied with the irrigation water may build up in the root zone, usually at the edge of the wetting pattern. On the other hand, drip irrigation avoids the high capillary potential of traditional surface-applied irrigation, which can draw salt deposits up from deposits below.
- the PVC pipes often suffer from rodent damage, requiring replacement of the entire tube and increasing expenses.
- Drip irrigation systems cannot be used for damage control by night frosts (like in the case of sprinkler irrigation systems)
Uses of Drip irrigation[Back to Contents]
Drip irrigation is used by farms, commercial greenhouses, and residential gardeners. Drip irrigation is adopted extensively in areas of acute water scarcity and especially for crops and trees such as coconuts, containerized landscape trees, grapes, bananas, ber, eggplant, citrus, strawberries, sugarcane, cotton, maize, and tomatoes.
Drip irrigation for garden available in drip kits are increasingly popular for the homeowner and consist of atimer, hose and emitter. Hoses that are 4 mm in diameter are used to irrigate flower pots.